Q. I am very paranoid about electricity.
but alias I have a problem. I think I have a bad circuit breaker. 3 outlets have no power.
the breaker threw about 5 times last week. now, all the receptacles are dead.
the breaker is not physically hot to the touch.
So I plan on killing the power but I've heard of stuff like a live neutral ?
What does this mean ? How would I test for it ?
I have a CAT III 6-600v ac/dc tester. it can also check continuity.
it also has a polarity function.
My plan is to kill the power and box(I have an outside pole/box) and inside panel,
then double check it that i have no power.
My question is detecting a "hot" neutral ? How can I be sure ?
A. Check for voltage between the ground wire( green or bare conductor) and the neutral or white wire. Usually if there is a load down line i.e. some device that is connected to the circuit that is in the on mode power will still be passing through the circuit. I also suggest checking the affected outlets for any bad connection, corrosion or damage and replace as necessary. You may also want to make sure that there are not any devices plugged in that is tripping the breaker. Breakers do go bad. After you kill the power go into the breaker box and swap wires from the suspected breaker and one of the same current rating that is known to be good and see if the problem reoccurs with the different breaker. If it does reoccur check the outlets. If it does not reoccur suspect the breaker.Look at my website for complete answers to your open circuit question. http://www.mobilehomemanufacturedhomes.com/How-To-Find-Open-Circuit.html
Update... It was both an open circuit at an outlet connection and intermittent circuit breaker. Double whammy, frustrating to troubleshoot.
Mobile Home and Manufactured Homes Questions and Answers for Electrical Plumbing Floor Roof Water Heater Switch Receptacle Outlet Plug Leaks Pipe A/C Repair Problems
Mobile Home Power Pole Mobile Home Service Electrical Diagram
If you need a mobile home power pole diagram for mobile home electric service for over head or under ground main breaker box and service entrance be sure to take a look at http://www.mobilehomemanufacturedhomes.com/MobileHomePowerPoleDiagram.html
Mobile Home Bathroom Tub Wall Surround
Q. We have a mobile home at Lake Havasu, California. The bathroom wall around the tub needs to be replaced. do you know where we can buy 4x8 vinyl (or whatever you recommend)panels for replacement? Any help you can give or someone in the Lake Havasu or Orange County, California area where we can purchase these panels would be greatly appreciated. Thanking you in advance for your attention to this matter.
A. If you have a 5' x 28'' bath tub or larger you can get a kit that comes in a flat box. I have added some tub surround suppliers on the main website Mobile Home Tub Surround Page. All home improvement stores have these. I have installed them in many mobile homes. Lowes, Home Depot and other stores also carry 4' x 8' sheets of materials you can use for bathroom wall panels on the paneling section. They are found in the mill works department where the windows and doors are, but will require a level of expertise to install them. Just be sure to use the tub surround adhesive and not liquid nails. It will bleed through. It is labeled for use on tub surrounds. Follow the directions and don't forget the caulk.
Update: DON, THANKS FOR ALL THE TIPS. MY HUSBAND AND SON COMPLETED THE JOB LAST WEEKEND. IT TURNED OUT VERY WELL (ALTHOUGH I HAVEN'T SEEN IT YET....JUST PICTURES).
A. If you have a 5' x 28'' bath tub or larger you can get a kit that comes in a flat box. I have added some tub surround suppliers on the main website Mobile Home Tub Surround Page. All home improvement stores have these. I have installed them in many mobile homes. Lowes, Home Depot and other stores also carry 4' x 8' sheets of materials you can use for bathroom wall panels on the paneling section. They are found in the mill works department where the windows and doors are, but will require a level of expertise to install them. Just be sure to use the tub surround adhesive and not liquid nails. It will bleed through. It is labeled for use on tub surrounds. Follow the directions and don't forget the caulk.
Update: DON, THANKS FOR ALL THE TIPS. MY HUSBAND AND SON COMPLETED THE JOB LAST WEEKEND. IT TURNED OUT VERY WELL (ALTHOUGH I HAVEN'T SEEN IT YET....JUST PICTURES).
Subscribe to:
Posts (Atom)